crafthub.tokyo
This is a 1/10 scale version of the construction safety fences often seen in Japan. STL data for FDM.
material: PLA
infill: 15%
support: no
perimeters 2
You can Download this model`s Full STL data from crafthub.io
This is a suspension Conversion kit. To use SuperScale2k20 SS Unit, This kit can use the full potential of the SS unit instantly. And you can get the realistic motion for your Yokomo YD-2E/S chassis.
You have to print out all parts by yourself. The material you should use is ABS or ColorFab HT, etc. otherwise the parts don’t have enough rigidity.PLA is not recommended
Nozzle Dia. 0.4 infill rate 30% vertical perimeters 3
Digital servo required
For Drift Car, Don’t need so much torque. 5-10kg may be enough, However, a metal-geared servo is required.
YD2E/YD2S Both types of data are included.
Only for this part, you have to use M3*6 screw, instead ofM3*10 screw to avoid not interfering with fixing the screw.
The Bumper fix screw is used to fix a servo Bracket
Front Strut (Remove the original Strut Tower)
Remove the ball end and fix it in the correct position Use a Tamiya Fluorne coated Stabilizer Ball connector set For the front, use this one.
Assemble the front Strut tower by adding M3*15 screws for the front. Do not over-tighten. Check for minimum play and movement.
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth.
Assembling the Rear Strut tower: (Assembled)
Use an M3*12 screw for the Rear. (Do not over-tighten)
Check minimum play (The arms should move easily.)
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth. Use a Tamiya Fluorine coated Stabilizer Ball connector set For the Rear, use this one.
Front side
Use the screw that Yokomo original Bumperfix used.
The *Front servo holder has 3 screws. The rear servo holder has 2 screws.
Rear Side
Remove the original bumper and replace it with the Servo holder.
About the Rear screw. Use the screw that yokomo originally used.
You need to install Arduino configuration software. Please download from the link below.
https://www.arduino.cc/en/Main/Software
You may download Arduino IDE software for your suitable platform. macOS or Win
Firmware needed from SuperScale2k20
SUPERSCALE_V1.2.ino.hex
*this firmware is pre-installed
First, connect the SS unit to the PC and set the offset to 0.
Next set BALANCE to 50.
The servo‘s neutral PWM value is almost 1500
FLpos 1500
RLpos 1500
*you should provide the power for SS Unit cause USB doesn’t provide enough power to move the servo neutral position.
Check all 4 servos in a neutral position, and then Set the servo horn like this.
Adjust The turnbuckle length, and then connect the servo and Strut arm.
All about the physical setup is done, please test the sample setting value.
This is the start value to set up the active suspension
For more detail, please refer to SS unit manual.
It will be better to change more high viscosity dumper oil.
Body mount post parts have compatibility with Yokomo Genuine Body mount rod. You can use your suitable third-party body mount. Or make a hole in the body and fix the body using a Body pin.
Do not use this file for commercial purposes without any permission.
This model was made with FDM 3Dprinter, the parts have some additive markings, however, no problem with those parts’ functions.
The product can download from www.crafthub.io
This kit is an STL Data kit for conversion of MSTRMX2.0 chassis with an active suspension system ”SuperScale2k20 SS Unit”.
• Come with All of the printable parts, without SS unit.
• Design for MST RMX2.0
• Active suspension and conventional suspension hybrid.
• Simple and reliable, easy to swap design
• Fully compatible original suspension geometry
Use the M3 screw, M3 Nut, and gently insert to the M3 Nut position.
Use M3*10 CapScrew to screw servos to chassis mount brackets.
The mount screw hole size is 2.8mm and optimizes the tolerance for M3 screws. The Servo’s output shaft should be on the side closest to chassis mount holes.
Remove the original Strut Tower. Remove the ball end and fix it in the same position
Use a Tamiya Fluorine coated Stabilizer Ball connector set For the front, use this one. (partsNo17)
Assemble the front Strut tower by adding M3*15 screws for the front. Do not over-tighten. Check for minimum play and movement.
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth.
Assembling the Rear Strut tower: (Assembled)
Using M3*12 screw for the Rear. (Do not over-tighten) Check minimum play (The arms should move easily.)
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth. Use a Tamiya Fluorine coated Stabilizer Ball connector set For the Rear, use this one. (partsNo17)
Front
Side screw use 3*15 Countersunk screw. For the center screw. Use the screw that MST originally used.
The *Front servo holder has 3 screws. The rear servo holder has 2 screws.
Rear
Remove the original bumper and replace it with the Servo holder. About the Rear screw. Use the screw that MST originally used.
Firmware needed from SuperScale2k20
SUPERSCALE_V1.2.ino.hex
*This firmware is pre-installed
You need to install Arduino configuration software. Please download it from the link below.
https://www.arduino.cc/en/Main/Software
You may download Arduino IDE software for your suitable platform. macOS or Win
First, connect the SS unit to the PC and set the offset to 0.
Next set BALANCE to 50.
The servo‘s neutral PWM value is almost 1500
FLpos 1500
RLpos 1500
*you should provide the power for SS Unit cause USB doesn’t provide enough power to move the servo neutral position.
Check all of the 4 servos in the neutral position, and then Set the servo horn like this.
This hone has a tapered servo shaft connection, so any spline servo can perfectly fit this servo horn. so this servo horn material is PETG. Use with Tapered washer like in the photo.
Adjust The turnbuckle length, and then connect the servo and Strut arm.
All about the physical setup is done, please test the sample setting value.
This is the start value to set up the active suspension
For more detail, please refer to SS unit manual.
It will be better to change more high viscosity dumper oil.
Ver 2 servo holder is an integrated body holder
Do not use this file for commercial purpose without any permission.
The product can download from www.crafthub.io
For all 1/10 scale Drift carｓ and 1/10 4wd crawlers for towing.
Even a very low downed drift car , you can carry on without any slopes.
STL data Realistic full functional model.
•Easy to assemble
•Optimized for 1/10scale RC Drift car. Ex Yokomo,Sakura, MST,etc.
•FDM printer with 0.4φOrifice nozzle.
•PLA or PETG can be used, in however summer season for outdoor use, I recommend
using PETG
•TPU for tires
Yokomo 4.8mmφ Ballend can use a tow vehicle coupler.
Assemble each of 4 axes. For smooth rotation of the tire, you can adjust it with a washer.
Mount the Tire rack use with double side tape.
Take attention to the Tire rack direction.
M3*8 screw
Hangingwire0.8mm
28servohorn.stl
Running the wire like that and adjusting the tension.
Adjust the wire length and fix it.
Do not use this file for commercial purposes without any permission. This model is designed to make FDM 3Dprinter, the parts have some additive markings, however, is no problem with those parts’ functions.
The product can download from www.crafthub.io
This kit is a detail-up kit for RCdriftCar. You can choose RHD/LHD. Connect the servo to the receiver’s unused channel, and mix the steering channel with your chosen channel.LED power is also taken from the receiver.
Note This data is optimized for 1/10Scale drift Car.
You have to print out all parts by yourself. The material you should use depends on the parts. Please choose the correct and affordable material.
0.4mm nozzle All of parts infill rate: 20%or more.
Haltech displays JPG image, Print out with sticker sheet.
Print out all parts with appropriate material. In this kit, we strongly recommend using Colorfabb HT filament.
Install 9g servo on gear holder. Servo comes with self-tapping screws.
Use this screw and assemble.
Check the part’s dimensions
And set the gear with self-tapping screws that come with the servo.
Check output 17T gear and shaft. Gear should apply to the hole side. When assembling them, apply appropriate glue.
With the M3*6Bottun screw, the shaft must spin easily.
Those parts and the Gear frame assemble with glue. When you assemble it, please gear’s backlash and check the gears move smoothly.
Using glue with a screw will be better.
Use pinch,adjust the mounting place and fix with double-side tape
Sample MST RMX2.0
Do not use this file for commercial purposes without any permission.
This model is designed to make FDM 3Dprinter, the parts have some additive markings, however, is no problem with those parts’ functions.
The product can download from www.crafthub.io