crafthub.tokyo
This is a 1/10 scale version of the construction safety fences often seen in Japan. STL data for FDM.
material: PLA
infill: 15%
support: no
perimeters 2
You can Download this model`s Full STL data from crafthub.io
This kit is an STL Data kit for conversion of MSTRMX2.0 chassis with an active suspension system ”SuperScale2k20 SS Unit”.
• Come with All of the printable parts, without SS unit.
• Design for MST RMX2.0
• Active suspension and conventional suspension hybrid.
• Simple and reliable, easy to swap design
• Fully compatible original suspension geometry
Use the M3 screw, M3 Nut, and gently insert to the M3 Nut position.
Use M3*10 CapScrew to screw servos to chassis mount brackets.
The mount screw hole size is 2.8mm and optimizes the tolerance for M3 screws. The Servo’s output shaft should be on the side closest to chassis mount holes.
Remove the original Strut Tower. Remove the ball end and fix it in the same position
Use a Tamiya Fluorine coated Stabilizer Ball connector set For the front, use this one. (partsNo17)
Assemble the front Strut tower by adding M3*15 screws for the front. Do not over-tighten. Check for minimum play and movement.
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth.
Assembling the Rear Strut tower: (Assembled)
Using M3*12 screw for the Rear. (Do not over-tighten) Check minimum play (The arms should move easily.)
The assembled strut tower needs a little bit of friction. If this part is too loose, the SS’s multiplier value can’t increase, and serious oscillation will occur and won’t stop. However, regular suspension linkage parts have to always be very smooth. Use a Tamiya Fluorine coated Stabilizer Ball connector set For the Rear, use this one. (partsNo17)
Front
Side screw use 3*15 Countersunk screw. For the center screw. Use the screw that MST originally used.
The *Front servo holder has 3 screws. The rear servo holder has 2 screws.
Rear
Remove the original bumper and replace it with the Servo holder. About the Rear screw. Use the screw that MST originally used.
Firmware needed from SuperScale2k20
SUPERSCALE_V1.2.ino.hex
*This firmware is pre-installed
You need to install Arduino configuration software. Please download it from the link below.
https://www.arduino.cc/en/Main/Software
You may download Arduino IDE software for your suitable platform. macOS or Win
First, connect the SS unit to the PC and set the offset to 0.
Next set BALANCE to 50.
The servo‘s neutral PWM value is almost 1500
FLpos 1500
RLpos 1500
*you should provide the power for SS Unit cause USB doesn’t provide enough power to move the servo neutral position.
Check all of the 4 servos in the neutral position, and then Set the servo horn like this.
This hone has a tapered servo shaft connection, so any spline servo can perfectly fit this servo horn. so this servo horn material is PETG. Use with Tapered washer like in the photo.
Adjust The turnbuckle length, and then connect the servo and Strut arm.
All about the physical setup is done, please test the sample setting value.
This is the start value to set up the active suspension
For more detail, please refer to SS unit manual.
It will be better to change more high viscosity dumper oil.
Ver 2 servo holder is an integrated body holder
Do not use this file for commercial purpose without any permission.
The product can download from www.crafthub.io
For all 1/10 scale Drift carｓ and 1/10 4wd crawlers for towing.
Even a very low downed drift car , you can carry on without any slopes.
STL data Realistic full functional model.
•Easy to assemble
•Optimized for 1/10scale RC Drift car. Ex Yokomo,Sakura, MST,etc.
•FDM printer with 0.4φOrifice nozzle.
•PLA or PETG can be used, in however summer season for outdoor use, I recommend
using PETG
•TPU for tires
Yokomo 4.8mmφ Ballend can use a tow vehicle coupler.
Assemble each of 4 axes. For smooth rotation of the tire, you can adjust it with a washer.
Mount the Tire rack use with double side tape.
Take attention to the Tire rack direction.
M3*8 screw
Hangingwire0.8mm
28servohorn.stl
Running the wire like that and adjusting the tension.
Adjust the wire length and fix it.
Do not use this file for commercial purposes without any permission. This model is designed to make FDM 3Dprinter, the parts have some additive markings, however, is no problem with those parts’ functions.
The product can download from www.crafthub.io